Onboard Dust Extractor for Skid Steers

Grydale Patented Onboard Dust Control Solution

Skid Steer Dust Extractor. Onboard Dust Control Solution Overview.

Skid Steers are often used on infrastructure projects both above and below ground and can generate hazardous silica dust that poses a health risk to construction workers.

Using our expertise in dust control we have developed, and patented a dust control solution specifically for Skid Steer and Posi-Track Loader units. These units operate multi-functional and rotary broom attachments to provide effective dust control at the source, without the use of water.

The onboard dust extraction system consists of flexible and solid ducting which runs between the Negative Air Pressure Sweeper (NAPS) and the dust control unit which is mounted at the rear of the Skid Steer. The dust control unit features a twin-stage axial fan (powered by an electric or hydraulic motor), fan diverter, patented dual SpinX separators to discharge heavy particles from the incoming air stream, floating filter frame, panel filter, and a hopper with slide gate discharge. The support frame has been designed to fit any Skid Steer make and model.

Onboard Dust Control. Key Features

Key Components of The Onboard Dust Extractor:

Negative Air Pressure Sweeper – houses a rotary brush with enclosed sides and two 200mm diameter spigots where ducting can be attached.

Heavy Particle Clean-Out Grates – To avoid blockages and improve filter life, heavy particles are captured in grates on the top of the sweeper house. These can be easily cleaned via the quick release mechanism.

Ducting – Both flexible and solid ducting is used to join the NAPS and dust control unit. The flexible ducting ensures the system is operational while manoeuvring on site. Solid ducting reduces the pressure loss across the system.

The Dust Control Unit, mounted at the rear of the Skid Steer features:

Axial Fan – a twin-stage axial fan is powered by an electric or hydraulic motor. The axial fan can also be run in reverse to act as a filter cleaning device.

Spinx Separators – Patented dual SpinX separators have been designed to operate at functional duct air velocity to separate the heavier dust particles from the incoming air stream – increasing filter life and effectiveness. c

Floating Filter Frame – housing the panel filter, cover plate and suspension springs. The filter frame is located in the main dust control unit and seals itself ensuring all air passes through the filter panel.

Panel Filter – follows the geometry of the dust collection unit housing which is design to assist air flow into the axial fan which is design to assist air flow into the axial fan.

Hopper – the hopper is used to collect dust particles after they are released from the panel filter.

Slide Gate – a manually actuated slide gate is used to empty the hopper onto the ground or any collection point.

Support Frame – designed to fit any Skid Steer Make and Model.The support frame features a pivot point and gas struts so the dust control unit can be tilted away from the rear of the skid steer to enable essential maintenance of the machine to take place.

Fan Diverter – used to direct axial fan exhaust away from the ground.

Control and Monitoring. Instrumentation.

The onboard dust extractor system includes CANbus instrumentation to allow the system to be controlled from within the Skid Steer cabin. Instrumentation includes:

Reverse Camera – so the operator can still reverse safely when any existing reverse camera is blocked by dust control unit.

Flood Light – positioned on the back of the dust control unit for visibility.

Operation Light – a green operation light is positioned on the unit to indicate that the dust control is operational.

Reverse Clean – the reverse clean cycle can be turned on by on operator via a push button.

Forward Motion Sensor – to activate the system when the machine is moving forward and stop the system when the unit is stationary (if required).

Battery Isolator – to isolate battery when not in use and for safety.

Hopper Capacity Light – illuminates when the hopper reaches capacity and needs to be emptied.

Differential Pressure Gauge – to indicate if there is a blockage in the duct run.

Solar Panel – to trickle charge the battery when not in use.

Simple Installation. Self-Install or Grydale Install Service.

We have designed the onboard Skid Steer dust extraction solution so that it can be easily self installed via the detailed assembly instruction manual. Alternatively we can install the system at our facilities or our Site Service Team can install at your workplace.

The onboard dust extraction solution can be easily operated and maintained by Skid Steer operators using documentation provided. Quick release mechanisms have been used throughout to support rapid maintenance and material discharge.

More Information? Contact Us.

If you would like more information on the onboard Skid Steer Dust Extractor or to arrange to see a demonstration, please complete the form below.

We try to respond to requests on the same business day, however if your enquiry is urgent please call our team on +1 (778) 897 2229. Our office hours are between 07:00 and 17:00 Monday to Friday.